![]() ![]() I'm have a 2005 Chrystler Pacific that started with a very little chatter around the front of engine, I got a P0016 code, a P2074, so changed the Map and Throttle Positioner Sensors, I also had to change a coil pack and a injector. I'm getting 2 different codes, P0016 & P0340 Code Please he.Shortly after that, it failed to start one time and I had the spark plugs, air cleaner and PCV valve replaced. The engine light came on several weeks ago and the first code (P0340) appeared. P0340 and P1391 codes-Need suggestions!Ģ001 Jeep Grand Cherokee Limited, 4.7L, V8, 80,500 miles, all wheel drive.BUT: have found out this part does not exist for my car. Pulled codes and got P0340 for camshaft position sensor circuit bank 1. Tries to start, but won't stay running more than 2 seconds. P0340-But part don't exist for my car! 2005 Pontiac Sunfire.Replace circuit wiring and/or connectors as required.Check the crankshaft position circuit as well.Replace the camshaft position sensor as required.Check the operation (voltage) of the camshaft position sensor.Check for continuity in the circuit wiring.Visually inspect all the wiring and connectors in the circuit.With a P0340 OBD-II trouble code, diagnosis can be tricky at times. the crankshaft position sensor may have failed.the camshaft position sensor may have failed.a wire or connector in the circuit could be grounded/shorted/broken.Lie in any part of the circuit - the sensor itself, the wiring, or the PCM.ĭon't just replace the CPS (camshaft position sensor) and think that will definitelyĪ code P0340 could mean one or more of the following has happened: Since it says circuit, that means the problem could This P0340 code indicates that a problem was detected in the camshaft position sensor So this engine code article applies to Nissan, Ford, Toyota, Chevrolet, Dodge, Honda, GMC, etc. It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may be slightly different depending on the model. This diagnostic trouble code (DTC) is a generic powertrain code. What do you guys suggest could you e-mail the results to me at Com? By the way I have checked the fuses and the timing belt by looking in the hole and seeing the chain move.P0340 Camshaft Position Sensor Circuit Malfunction Technical DescriptionĬamshaft Position Sensor Circuit Malfunction What does that mean? I think it might be the crank sensor, but I do not want to change it unless that is deffiently the problem, and I can't even find the location of the crank sensor, could you guys please help me? I am not even getting a check engine light on, telling me the problem. It was snowing out that day and I even went through the whole car with a hair dryer to melt the snow because some got in, under the hood. I also checked the spark by taking out a spark plug and grounding it to a bolt in the frame and had 2 other people even check it and still no spark, well at least me nor them saw one. I checked all wire connections, coil pack, battery, checked fuel pump by turning the key over and listening for a noise and it made the niose like the fuel pump was working, checked grounds and even starter wire connections, and nothing seemed to be out of the ordinary. I recently was driving down the road and when I turned on the lights, soon after my battery light came on, drove a little farther and my engine just shut off and wouldn't start again. On 2.4L SRT-4, install the lower inner cooler hose to metal tube and tighten clamp. Install the Structural Collar, refer to the Engine, Structural Collar Removal and Installation section. Ĭonnect and lock the electrical connector to the crankshaft position sensor. Install and tighten the crankshaft position sensor bolt and tighten to 9 Nm (80 15 in. Use a twisting motion when installing the sensor. Remove the crankshaft position sensor bolt.įig.3 Crankshaft Position Sensor - 2.4L TurboĬheck O-ring for damage and lubricate the O-ring with engine oil before installing sensor. Unlock and disconnect the electrical connector to the crankshaft position sensor. Remove the Structural Collar, refer to the Engine, Structural Collar Removal and Installation section. On 2.4L SRT-4, remove the lower inner cooler hose from the metal tube.įig.2 Structural Collar And Bending Strut - (Automatic Transaxle Equipped) The Crankshaft Position Sensor is in the front of the engine block just under the starter motor. Fig.1 Crankshaft Position Sensor Location ![]()
0 Comments
Leave a Reply. |